Contact
Life
Water-based 1-component finish for wooden floors.
Select variant
Life
satin
Properties
- Good price/performance ratio
- Can be used in full structure
- Balanced properties
- High filling capacity
- Easy and safe application
Further information
Range of use
Suitable for parquet and wooden floors.
| Art.-no. |  |  |  |
|---|---|---|---|
11524-900003-22-000 | 5 l | 4 | 128 |
11524-900003-32-000 | 10 l | - | 60 |
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P120 or finer, alternatively Sanding Net P120 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Alternative Set-Up recommendation without primer:
Only with rigid bonding for wood species oak, ash, maple and light beech. For moisture-sensitive woods, parquet on underfloor heating and in restoration cases we recommend only applying only one coat of finish per day.- Prepare the substrate professionally.
- Roll on Life.
- Drying.
- Roll on a second layer of Life.
- Drying.
- Intermediate sanding.
- Roll on a final layer of Life.
Suitable product combinations
We recommend using a primer:
to minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime.
- VivaPrime.
- PrimaSeal Plus (contains solvent).
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
Suitable Loba products
EasyPrime
PerforatedPad & DustPad
Roller Deluxe 120
Roller Microfibre 100-120
VivaPrime
Whitener
ParkettCare
- satin
Coating bucket, bucket liner
Cleaner
Canister opener
Small roller for edges
Suitable Wakol products
D 1640
D 1690
MS 228
MS 230
MS 232
MS 260
MS 261
MS 262
MS 265
MS 269
MS 290
MS 292
PU 210
PU 215
PU 216
PU 220
PU 225
PU 385
Life
semi-gloss
Properties
- Good price/performance ratio
- Can be used in full structure
- Balanced properties
- High filling capacity
- Easy and safe application
Technical data sheets
Stress level
1
2
3
4
5
6
7
8
9
10
Residential
Commercial
Extreme
Further information
Range of use
Suitable for parquet and wooden floors.
| Art.-no. | | | |
|---|---|---|---|
11524-900001-22-000 | 5 l | 4 | 128 |
11524-900001-32-000 | 10 l | - | 60 |
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P120 or finer, alternatively Sanding Net P120 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Alternative Set-Up recommendation without primer:
Only with rigid bonding for wood species oak, ash, maple and light beech. For moisture-sensitive woods, parquet on underfloor heating and in restoration cases we recommend only applying only one coat of finish per day.- Prepare the substrate professionally.
- Roll on Life.
- Drying.
- Roll on a second layer of Life.
- Drying.
- Intermediate sanding.
- Roll on a final layer of Life.
Suitable product combinations
We recommend using a primer:
to minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime.
- VivaPrime.
- PrimaSeal Plus (contains solvent).
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
Suitable Loba products
PerforatedPad & DustPad
EasyPrime
Roller Deluxe 120
VivaPrime
Whitener
ParkettCare
- silk gloss
Cleaner
Coating bucket, bucket liner
Small roller for edges
Refresh
Amberizer
Suitable Wakol products
D 1640
D 1690
MS 228
MS 230
MS 232
MS 260
MS 261
MS 262
MS 265
MS 269
MS 290
MS 292
PU 210
PU 215
PU 216
PU 220
PU 225
PU 385
Life
gloss
Properties
- Good price/performance ratio
- Can be used in full structure
- Balanced properties
- High filling capacity
- Easy and safe application
Further information
Range of use
Suitable for parquet and wooden floors.
| Art.-no. | | | |
|---|---|---|---|
11524-900002-22-000 | 5 l | 4 | 128 |
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P180 or finer, alternatively Sanding Net P180 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Suitable product combinations
We recommend using a primer:
to minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime.
- VivaPrime.
- PrimaSeal Plus (contains solvent).
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
Suitable Loba products
EasyPrime
PerforatedPad & DustPad
Roller Deluxe 120
Roller Microfibre 100-120
VivaPrime
Refresh
Roller frame, roller extension
Small roller for edges
Cleaner
Whitener
Amberizer
Suitable Wakol products
D 1640
D 1690
MS 228
MS 230
MS 232
MS 260
MS 261
MS 262
MS 265
MS 269
MS 290
MS 292
PU 210
PU 215
PU 216
PU 220
PU 225