• Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Usable up to 2 hours after mixing.
• The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
• The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
• In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
• To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
• Transfer material to a LOBA varnish bucket before applying.
• Shake the contents well.
• Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems

Thinner / Mixing

Application tool / application rate

Drying time

• Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
• Light use after 24 hours.
• Full use and covering possible after 5 days.
• The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
• Drying times are valid for +20°C and 50% relative humidity.

Intermediate sanding

Use on parquet and hardwood floors:

• Prepare and prime the substrate properly.
• Allow the primer to dry as specified.
• Apply by roller.
• Dry.
• Intermediate sanding.
• Apply second coating layer by roller.

Use on cork:

Untreated natural cork:

• Apply three layers of coating by roller.
• Allow the first layer to dry overnight (reduces the risk of granule swelling).
• Intermediate sanding before the final application.

Prefinished cork

Renovation / recoating of old coatings

Coloring tip

Linoleum and PVC:

Suitable product combinations

We recommend using a primer:

• EasyPrime
• VivaPrime
• 2K Intensive
• PrimaSeal Plus (contains solvent)

Additives

• Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Usable up to 2 hours after mixing.
• The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
• The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
• In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
• To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
• Transfer material to a LOBA varnish bucket before applying.
• Shake the contents well.
• Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems

Thinner / Mixing

Application tool / application rate

Drying time

• Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
• Light use after 24 hours.
• Full use and covering possible after 5 days.
• The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
• Drying times are valid for +20°C and 50% relative humidity.

Intermediate sanding

Use on parquet and hardwood floors:

• Prepare and prime the substrate properly.
• Allow the primer to dry as specified.
• Apply by roller.
• Dry.
• Intermediate sanding.
• Apply second coating layer by roller.

Use on cork:

Untreated natural cork:

• Apply three layers of coating by roller.
• Allow the first layer to dry overnight (reduces the risk of granule swelling).
• Intermediate sanding before the final application.

Prefinished cork

Renovation / recoating of old coatings

Coloring tip

Linoleum and PVC:

Suitable product combinations

We recommend using a primer:

• EasyPrime
• VivaPrime
• 2K Intensive
• PrimaSeal Plus (contains solvent)

Additives

• Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Usable up to 2 hours after mixing.
• The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
• The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
• In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
• To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
• Transfer material to a LOBA varnish bucket before applying.
• Shake the contents well.
• Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems

Thinner / Mixing

Application tool / application rate

Drying time

• Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
• Light use after 24 hours.
• Full use and covering possible after 5 days.
• The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
• Drying times are valid for +20°C and 50% relative humidity.

Intermediate sanding

Use on parquet and hardwood floors:

• Prepare and prime the substrate properly.
• Allow the primer to dry as specified.
• Apply by roller.
• Dry.
• Intermediate sanding.
• Apply second coating layer by roller.

Suitable product combinations

We recommend using a primer:

• EasyPrime
• VivaPrime
• 2K Intensive
• PrimaSeal Plus (contains solvent)

Additives