Life
1-component water-based finish for hardwood flooring.
Select variant
Life
satin
Properties
- Good price/performance ratio
- Balanced properties
- Excellent build
- Easy application
- Suitable for all light colored North American wood species.



More information
Recommended use
Suitable for wood flooring.
| Art.-no. | Item-# | ||
|---|---|---|---|
11524-900003-32-250 | LO-FI-328 | 2.5 gal. | 75 |
- For professional use only!
- Recommended climate conditions are 55°F-80°F/40-75%rH.
- BEFORE USING, READ AND UNDERSTAND ALL LABEL INSTRUCTIONS AND MATERIAL SAFETY DATA SHEETS.
- For technical advice call our Loba-Wakol Technical Service at 1-800.230.6456.
- Sand and prepare floors according to NWFA guidelines.
- WARNING! If you scrape, sand, or remove old paint from wood floors, you may release lead dust. Follow local and/or federal requirements for lead removal. Before you start, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
- ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.
- Shake material well before use.
- Do not thin. Do not add water.
- Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
- Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol wood flooring adhesives may be found in the "Connected Systems Matrix": https://www.loba.de/us/connected-systems/
Application Tool
LOBA Micro 120 RollerT-barCoverage
500-600 square feet per gallon per coat.Drying time
- Earliest possible recoating after 2-3 hours.
- Fully cured after 5 days.
- If there is a delay in drying wait until you can see that the surface is completely dry.
Setup recommendation for light colored North American wood types:
- Apply first coat of Life.
- Allow to dry for 2-3 hours minimum (do not exceed 24 h).
- Apply second coat of Life.
- Allow to dry overnight.
- Intermediate sanding with LOBASAND 180-220 perforated pad (or equivalent) to remove grain raise.
- Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
- Apply third coat of Life.
- An additional roll application may be necessary to achieve homogeneous fullness.
Alternative setup for dark/exotic wood types:
- Apply one coat of EasyPrime according to directions.
- Allow to dry for 2-3 hours minimum (do not exceed 24 h).
- Apply first coat of Life.
- Allow to dry overnight.
- Intermediate sanding with LOBASAND 180-220 perforated pad (or equivalent) to remove grain raise.
- Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
- Apply second coat of Life.
- An additional roll application may be necessary to achieve homogeneous fullness.
Screen and Recoat
- Clean floor, abrade with LOBASAND 180-220 grit perforated pad(or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
- Apply finish following instructions.
- Always prepare test areas to determine compatibility, appearance, and desired results.
- Do NOT use on floors finished with UV cured, oxide containing, factory applied finishes.
Compatibility
When this product is used in combination with other LOBA products the technical information of these products must be followed. Refer to the Technical Data Sheets. LOBA cannot guarantee the suitability of products other than LOBA or the bond of the existing coating to the substrate.Consumption calculator
Area
sq ft
Required units
= ?
Application device
Coats
Life
semi-gloss
Properties
- Good price/performance ratio
- Balanced properties
- Excellent build
- Easy application
- Suitable for all light colored North American wood species.



More information
Recommended use
Suitable for wood flooring.
| Art.-no. | Item-# | ||
|---|---|---|---|
11524-900001-32-250 | LO-FI-329 | 2.5 gal. | 75 |
- For professional use only!
- Recommended climate conditions are 55°F-80°F/40-75%rH.
- BEFORE USING, READ AND UNDERSTAND ALL LABEL INSTRUCTIONS AND MATERIAL SAFETY DATA SHEETS.
- For technical advice call our Loba-Wakol Technical Service at 1-800.230.6456.
- Sand and prepare floors according to NWFA guidelines.
- WARNING! If you scrape, sand, or remove old paint from wood floors, you may release lead dust. Follow local and/or federal requirements for lead removal. Before you start, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
- ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.
- Shake material well before use.
- Do not thin. Do not add water.
- Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
- Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol wood flooring adhesives may be found in the "Connected Systems Matrix": https://www.loba.de/us/connected-systems/
Application Tool
LOBA Micro 120 RollerT-barCoverage
500-600 square feet per gallon per coat.Drying time
- Earliest possible recoating after 2-3 hours.
- Fully cured after 5 days.
- If there is a delay in drying wait until you can see that the surface is completely dry.
Setup recommendation for light colored North American wood types:
- Apply first coat of Life.
- Allow to dry for 2-3 hours minimum (do not exceed 24 h).
- Apply second coat of Life.
- Allow to dry overnight.
- Intermediate sanding with LOBASAND 180-220 perforated pad (or equivalent) to remove grain raise.
- Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
- Apply third coat of Life.
- An additional roll application may be necessary to achieve homogeneous fullness.
Alternative setup for dark/exotic wood types:
- Apply one coat of EasyPrime according to directions.
- Allow to dry for 2-3 hours minimum (do not exceed 24 h).
- Apply first coat of Life.
- Allow to dry overnight.
- Intermediate sanding with LOBASAND 180-220 perforated pad (or equivalent) to remove grain raise.
- Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
- Apply second coat of Life.
- An additional roll application may be necessary to achieve homogeneous fullness.
Screen and Recoat
- Clean floor, abrade with LOBASAND 180-220 grit perforated pad(or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
- Apply finish following instructions.
- Always prepare test areas to determine compatibility, appearance, and desired results.
- Do NOT use on floors finished with UV cured, oxide containing, factory applied finishes.
Compatibility
When this product is used in combination with other LOBA products the technical information of these products must be followed. Refer to the Technical Data Sheets. LOBA cannot guarantee the suitability of products other than LOBA or the bond of the existing coating to the substrate.Consumption calculator
Area
sq ft
Required units
= ?